Vintage Gruen: 1930's » Stainless Steel Quadron

Home » The Gruen Model Database » 1930's » Stainless Steel Quadron

Show: Today's Messages :: Polls :: Message Navigator
E-mail to friend

Re: stainless steel Quadron [message #6260 is a reply to message #6093]

Mon, 16 November 2015 05:36

JackW
Messages: 2013
Registered: May 2013
Location: Denver

Gruen Authority
Head Janitor
Site Admin

Well, I gotta say thank you to Jason. He sent me a staff and I had the watch up and running. It was cased even. As it was sitting on the timing machine, there was some noise in the trace so I decided to run it through the demagnetizer. The noise stopped as did the watch. I opened it up to look and some how the staff broke. I've almost always run my watches as the last step through the demagnetizer. The flabergasting aspect is that it happened twice on this watch. The first time I chalked it up to the staff pivot was already cracked and it went. I'm not of the opinion that a) I've been lucky in the past and b) these 157 staffs are more fragile. Anyway, watch is running now. Getting good at cutting out staffs and sharpening my carbide gravers.

index.php?t=getfile&id=2593&private=0

Also, the staffs from Borel are a wee-bit small on the diameter of the roller seat. The one Jason sent me was a spot-on fit. The one from Borel came in a envelope that was marked Bestfit. I had to do a little peening with the staking set to reduce the diameter of the hole of the roller at one end so that it would stay on. They are friction fit; just needed more friction.

All I know is based on hard work & writing by others. I can only aspire to augment this body of knowledge. If I am wrong it is because of my own failings. -me

"If I have seen farther it is by standing on the shoulders of giants." - Newton

Report message to a moderator

[Message index]

		Stainless Steel Quadron By: JackW on Sun, 27 September 2015 19:45
		Re: stainless steel Quadron By: Barney Green on Mon, 28 September 2015 09:58
		Re: stainless steel Quadron By: afire on Mon, 28 September 2015 15:04
		Re: stainless steel Quadron By: JackW on Mon, 28 September 2015 15:28
		Re: stainless steel Quadron By: afire on Mon, 28 September 2015 21:10
		Re: stainless steel Quadron By: Gary on Tue, 29 September 2015 00:02
		Re: stainless steel Quadron By: JackW on Tue, 29 September 2015 00:43
		Re: stainless steel Quadron By: afire on Tue, 29 September 2015 19:39
		Re: stainless steel Quadron By: JackW on Mon, 16 November 2015 05:36
		Re: stainless steel Quadron By: Case on Fri, 17 September 2021 17:55
		Re: stainless steel Quadron By: afire on Fri, 17 September 2021 18:25
		Re: stainless steel Quadron By: Ephemerald on Sat, 18 September 2021 02:21
		Re: stainless steel Quadron By: Case on Sun, 19 September 2021 02:26

Previous Topic:	Ristside Varsity 1938
Next Topic:	Two-Diamond Brookline - possible Baguette 519

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Jul 11 13:25:07 UTC 2025

Total time taken to generate the page: 0.00928 seconds